Product code:

Lithofin KF Stain-Stop 1 Litre


    Key Features

    • Ready to use
    • Contains solvents
    • Effective for many years
    • For Indoor and Outdoor use
    • Store closed, in a cool area for up to 3 years

    Product Specification

    Product Overview

    A special product from the LITHOFIN-Range for ceramic and quarry tiles (KF). This ready-to-use special impregnator is solvent based and contains high quality water and oil resistant components.

    This special impregnator protects absorbent, stain-sensitive ceramic finishes and grout against stains. Prevents penetration of oil, grease and water to a high degree, making maintenance easier. Poses no health hazard once the product has dried.

    Lithofin KF Stain-Stop penetrates into the surface and coats the capillaries with an extremely thin, invisible film. Oil, grease and water are not absorbed by the surface, but instead remain on the surface. During this time, dirt can easily be removed without leaving stains. The effectiveness depends on the amount of product absorbed by the surface. The characteristic appearance of the surface material is not or only slightly altered.


    Density: approx. 0,78 g/cm³

    Appearance: liquid, colourless, clear

    Odour: aromatic pH-Value: n.a.

    Flash Point: approx. 23°C

    Reduction in Water Absorption: 90 to 95%

    For protecting unglazed ceramics against stains and for facilitating every-day maintenance. Highly recommended for use in kitchens, bathrooms and other areas which may come into contact with water and oil. Please Note: Lithofin KF Stain-Stop does not or only slightly affect the slip resistance properties of the surface.

    The surface to be treated must be completely dry and clean. Always test the product in an inconspicuous area prior to use. Areas should be treated in sections of approx. 10 to 15m². On highly absorbent surfaces: evenly and generously apply Lithofin KF Stain-Stop with a brush or roller. Avoid foam. On less absorbent surfaces: use a brush or a cloth. After approx. 20 minutes, apply Lithofin KF Stain-Stop again to ensure that the entire surface is saturated. Then carefully remove all surface residues with a cloth. On large areas use a polishing machine with a white pad. Do not allow any product to dry on the surface. On highly absorbent surfaces, a second application after approx. 24 hours may be necessary. Attention! the liquid product must sink into the surface. Do not allow the product to dry on the surface. Dry residues will not be removable once product is fully cured. Always try the product in an inconspicuous area prior to use. Lithofin KF Stain-Stop can only be used on absorbent and completely dry surfaces. Glass, ceramics, wood, and other surfaces sensitive to solvents must be protected against splashes. Application Temperature: the temperature of the surface should be between 5°C and 25°C. Switch off under floor heating. Drying Time: most solvents will evaporate within two hours. The product will be fully effective after approx. 48 hours. Coverage: depends on the absorbency of the material. Estimates: clay slabs: 3 to 8 m²/L unglazed quarry tiles: 8 to 15 m²/L Durability: 3 to 5 years in outdoor areas. Indoors, the durability depends on the care products used. Strong degreasing or layer forming products are not suitable. For regular maintenance, we recommend Lithofin KF EasyCare.

    Delivery & Returns


    At TileMarket, we like to keep our prices as competitive, and honest as possible, which is why we charge carriage on all deliveries, subject to weight and location. We think this is the fairest and most reasonable option, rather than charging a flat fee. This way, we can keep our stock prices low, which you our customer can benefit from.

    • Fast delivery times
    • Contact prior to your delvery
    • Free delivery on orders over £399


    In accordance with the Selling Regulations and law, the following applies to all orders made via E-Commerce contracts. The Customer is allowed to return the Goods within seven working days for a refund; this excludes all shipping costs incurred. However if any of the following points have been breached the returns contract entered will be void

    • The product box has been opened
    • The products have not been fixed onto a surface
    • Any visual or internal damage has been done
    • If the returned Goods received by the Company are not in a sellable/as sold condition.